Refer to the exhibit. Host A and Host B are connected to the Catalyst 3550 switch and have beenassigned to their respective VLANs. The rest of the 3550 configuration is the default configuration.Host A is able to ping its default gateway， 10.10.10.1， but is unable to ping Host B. Given theoutput displayed in the exhibit， which statement is true？（）
A.HSRP must be configured on SW1
B.A separate router is required to support interVLAN routing
C.Interface VLAN 10 must be configured on the SW1 switch
D.The global config command ip routing must be configured on the SW1 switch
E.VLANs 10 and 15 must be created in the VLAN database mode
F.VTP must be configured to support interVLAN routing
您可能感興趣的試卷
你可能感興趣的試題
A.The access layer is the initial point at which traffic enters the network. Traffic is marked （orremarked） at Layers 2 and 3 by the access switch as it enters the network， or is "trusted" that it isentering the network with the appropriate tag
B.No traffic marking occurs at the core layer. Layer 2/3 QoS tags are trusted from distributionlayer switches and used to prioritize and queue the traffic as it traverses the core
C.Traffic inbound from the access layer to the distribution layer can be trusted or reset dependingupon the ability of the access layer switches. Priority access into the core is provided based onLayer 3 QoS tags
D.IP precedence， DSCP， QoS group， IP address， and ingress interface are Layer 2 characteristics that are set by the access layer as it passes traffic to the distribution layer. Thedistribution layer， once it has made a switching decision to the core layer， strips these off
E.MAC address， Multiprotocol Label Switching （MPLS）； the ATM cell loss priority （CLP） bit， theFrame Relay discard eligible （DE） bit， and ingress interface are established by the voicesubmodule （distribution layer） as traffic passes to the core layer
F.The distribution layer inspects a frame to see if it has exceeded a predefined rate of trafficwithin a certain time frame， which is typically a fixed number internal to the switch. If a frame isdetermined to be in excess of the predefined rate limit， the CoS value can be marked up in a waythat results in the packet being dropped
A.QoS classified at layer 3 using IP precedence or DSCP
B.Guaranteed rate service
C.Implemented using FIFO queues
D.All traffic has an equal chance of being dropped
A.Quality of Service （QoS）
B.Intelligent platforms
C.Mobility and scalability
D.Security
E.High availability
A.The use of a queuing method that will give VoIP traffic strict priority over other traffic
B.The use of RTP header compression for the VoIP traffic
C.The proper classification and marking of the traffic as close to the source as possible
D.The use of 802.1QinQ trunking for VoIP traffic
E.The use of WRED
A.IP phones require inline power and must be in separate VLAN to receive inline power
B.IP telephony applications require prioritization over other traffic as they are more delaysensitive
C.IP phones can only receive IP addresses through DHCP if they are in separate VLAN
D.The CDP frames from the IP phone can only be recognized by the switch if the phone is in anauxiliary vlan
According to the information presented in the following exhibit， can you tell me the reason that thetrust state of interface FastEthernet 0/3 displays "not trusted"？（）
A.The command mis qos needs to be turned on in global configuration mode
B.DSCP map needs to be configured for VOIP
C.ToS has not been configured
D.There is not a Cisco Phone attached to the interface
A.Variable queue delays
B.Packet drops
C.Transmitting too many small packets
D.Compression
A.Mis-routed packets
B.Excess jitter
C.Delay of critical traffic
D.Packet loss due to congestion
E.Data link layer broadcast storms
F.FTP connections unsuccessful
Refer to the exhibit. What is the effect when the switchport priority extend cos 3 command isconfigured on the switch port interface connected to the IP phone？（）
A.Effectively， the trust boundary has been moved to the PC attached to the IP phone
B.The computer is now establishing theCoS value and has effectively become the trust boundary
C.The IP phone is enabled to override with aCoS value of 3 the existing CoS marking of the PCattached to the IP phone
D.The switch will no longer tag incoming voice packets and will extend the trust boundary to thedistribution layer switch
E.RTP will be used to negotiate aCoS value based upon bandwidth utilization on the link
Based on the graphic below， which Catalyst switch interface command should be issued in orderfor the switch to instruct the phone to override the incoming CoS from the CK-PC before sendingthe packet to the switch？（）
A.switchport priority extend cos 11
B.switchport priority extend cos 2
C.mis qos cos 2
D.mis qos cos 2 override
最新試題
As a network engineer， do you know for what purpose SDM uses Security Device Event Exchange（SDEE）？（）
Drag the DSL technologies on the left to their maximum（down/up） data rate values on the below.
This item contains several questions that you must answer. You can view these questions byclicking on the Questions button to the left. Changing questions can be accomplished by clickingthe numbers to the left of each question. In order to complete the questions， you will need to referto the SDM and the topology， neither of which is currently visible. To gain access to either thetopology or the SDK click on the button to left side of the screen that corresponds to the sectionyou wish to access. When you have finished viewing the topology the SDK you can return to yourquestions by clicking on the Questions button to the left.Which IPSec rule is used for the Olympia branch and what does it define？（）
Drag and drop question. The upper gives the MPLS functions， the bottom describes the planes.Drag the above items to the proper location at the below
Identify the recommended steps for worm attack mitigation by dragging and dropping them into thetarget area in the correct order.
As a network technician， do you know what is a recommended practice for secure configurationmanagement？（）
Drag and drop the steps in the process for provisioning a cable modem to connect to a headendon the above to the below in the order defined by the DOCSIS standard.
Drag each element of the Cisco IOS Firewall Feature Set from the above and drop onto itsdescription on the below.
Drag the IPsec protocol description from the above to the correct protocol type on the below.（Notall descriptions will be used）Drag and Drop question， drag each item to its proper location.
Drag the protocols that are used to distribute MPLS labels from the above to the target area on thebelow.（Not all options will be used）