A. Configure the switch to be in VTP client mode.
B. Configure the switch to be in VTP domaint mode.
C. Configure the switch to be in VTP transparent mode.
D. Configure the switch to be in VTPv2.
您可能感興趣的試卷
你可能感興趣的試題
A. proxy.
B. dual-stack
C. tunneling
D. dot1q
A. user EXEC mode
B. global configuration mode
C. privileged EXEC mode
D. auxiliary setup mode
A. when a packet is received from an 802.1Q trunk,the vlan id can be determined from the source MAC address table.
B. unkown unicast frames are retransmitted only to the ports that belong to the same vlan
C. ports between switches should be configured in access mode so that vlans can span across the ports
D. broadcast and multicast frames are retransmitted to ports that are configured on different vlan.
A. an OSPF update for network 192.168.0.0/16
B. a static router to network 192.168.10.0/24
C. a static router to network 192.168.10.0/24 with a local serial interface configured as the next hop
D. a RIP update for network 192.168.10.0/24
E. a directly connected interface with an address of 192.168.10.254/24
F. a default route with a next hop address of 192.168.10.1
A. session
B. network
C. physical
D. data link
E. transport
A. 172.16.16.0
B. 172.16.24.0
C. 172.16.0.0
D. 172.16.28.0
A. show frame-relay end-to-end
B. show frame-relay map
C. show frame-relay lmi
D. show frame-relay pvc
A. Frame Relay
B. HDLC
C. x.25
D. PPP
A. after broken links are re-established
B. in an improperly implemented redundant topology
C. when upper-layer protocols require high reliability
D. during high traffic periods
E. when a dual ring topology is in use
A. enbale password c1sco
B. secret enable c1sco
C. password enable c1sco
D. enable secret c1sco
最新試題
What is the purpose of the cisco Vlan Trunking protocol?（）
Which command is used to display the collection of OSPF link states?（）
The network administrator cannot to switch 1 over a telnet session,although the hosts attached to switch 1 can ping the interface Fa0/0 of the router.Given the information in the graphic and assuming that the router and switch2 are configured properly,which of the following commands should be issued on switch 1 to correct this problem?（）
Which address is the IPV6 all-RIP-routers muticast group address that is used by RIPng as the destaion address?（）
After the show ip route command has been entered,the follwing routes are displayed.Which route will not be entered into the routing table of a neighboring router?（）
A network administrator is trying to add a new router into an established OSPF network.The networks attached to the new router do not appear in the routing tables of the other OSPF routers.Given the information in the partial configuration shown below,what configuration error is causing this problem?（）Router(config)#router ospf 1Router(config-router)#network 10.0.0.0 255.0.0.0 area 0
A network administrator needs to configure a serial link between the main office and a remote location.The router at the remote office is a non-cisco router. How should the network administrator configure the serial interface of the main office router to make the connection?（）
Which cisco ios command can help to determine the timing of various debug events,relative to each other,when you are debugging a complicated router issue?（）
Which name describes an IPV6 host-enable tunneling technique that uses IPV4 UDP,does not require dedicated gateway tunnels,and can pass through existing IPV4 NAT gateways?（）
Three access ports have been installed and configured to a small office.What term defines the wireless topology?（）