Refer to the exhibit. VTP has been enabled on the trunk links between all switches within the TEST domain. An administrator has recently enabled VTP pruning. Port 1 on Switch 1 and port 2 on Switch 4 are assigned to VLAN 2. A broadcast is sent from the host connected to Switch 1. Where will the broadcast propagate?()
A.Every switch in the network receives the broadcast and will forward it out all ports.
B.Every switch in the network receives the broadcast,but only Switch 4 will forward it out port 2.
C.Switches 1,2,and 4 will receive the broadcast,but only Switch 4 will forward it out port 2.
D.Only Switch 4 will receive the broadcast and will forward it out port 2.
您可能感興趣的試卷
你可能感興趣的試題
A.30 seconds
B.5 minutes
C.1 minute
D.10 seconds
E.5 seconds
F.None of the other alternatives apply
A.A root VTP server
B.A trunk port
C.VTP priority
D.VLAN 1
E.None of the other alternatives apply
A.STP root status
B.VTP mode
C.Negotiation status
D.Management domain
E.Configuration revision number
A.Devices use DHCP to request their VLAN.
B.Attached devices are unaware of any VLANs.
C.Devices are assigned to VLANs based on their MAC addresses.
D.Devices are in the same VLAN regardless of which port they attach to.
A.VMPS server lookup is required
B.Easy to configure
C.Easy of adds,moves,and changes
D.Based on MAC address of the connected device
Given the above partial configuration, which two statements are true about VLAN traffic?()
A.VLANs 1-5 will use fa0/10 as a backup only.
B.VLANs 6-10 will use fa0/10 as a backup only.
C.VLANs 1-5 will be blocked if fa0/10 goes down.
D.VLANs 1-10 are configured to load share between fa0/10 and fa0/12.
E.VLANs 6-10 have a port priority of 128 on fa0/10.
A.Configuration revision number
B.Configuration revision flag field
C.Configuration revision reset switch
D.Configuration revision database
E.None of the other alternatives apply
A.VLAN 1003
B.VLAN 1
C.VLAN ON
D.VLAN A
E.VLAN 0
A.optimized transport structure
B.high port density
C.boundary definition
D.data encryption
E.local VLANs
F.route summaries
A.Each switch port is assigned to a specific VLAN.
B.Dynamic VLANs require a VLAN Membership Policy Server.
C.Devices are in the same VLAN regardless of which port they attach to.
D.Dynamic VLAN assignments are made through the command line interface.
最新試題
Refer to the exhibit and the partial configuration of switch SW_A and SW_B. STP is configured on all switches in the network. SW_B receives this error message on the console port:00:06:34: %CDP-4-DUPLEX_MISMATCH: duplex mismatch discovered on FastEthernet0/5 (not half duplex), with SW_A FastEthernet0/4 (half duplex) , with TBA05071417(Cat6K-B) 0/4 (half duplex). What would be the possible outcome of the problem?()
Refer to the exhibit. Which statement is true about the output?()
Refer to the exhibit. For what purpose is the command show ip cef used?()
During routine maintenance, it became necessary to shutdown G1/0/1 on DS1 and DS2. All other interface were up. During this time, DS1 became the active device for Vlan104’s HSRP group. As related to Vlan104’s HSRP group. What can be done to make the group function properly ? ()
Which option correctly identifies the Cisco IOS switching methods in descending order from the fastest method to the slowest method?()
Refer to the exhibit. Switch S2 contains the default configuration. Switches S1 and S3 both have had the command spanning-tree mode rapid-pvst issued on them. What will be the result?()
Which two statements are true about BPDU port-guard and BPDU filtering?()
Refer to the exhibit. LACP has been configured on Switch1 as shown. Which is the correct command set to configure LACP on Switch2?()
During routine maintenance, G1/0/1 on DS1 was shutdown. All other interface were up. DS2 became the active HSRP device for Vlan101 as desired. However, after G1/0/1 on DS1 was reactivated. DS1 did not become the active HSRP device as desired. What need to be done to make the group for Vlan101 function properly ? ()
What must be the same to make multiple switches part of the same Multiple Spanning Tree (MST)?()