A.SW1#show swithport port-security interface FastEthernet 0/12
B.SW1# show swithport port-secure interface FastEthernet 0/12
C.SW1# show port-secure interface FastEthernet 0/12
D.SW1#show running-config
E.SW1#show port-security interface FastEthernet 0/12
您可能感興趣的試卷
你可能感興趣的試題
A.Administratively shut down the interfaces.
B.Physically secure the interfaces.
C.Configure a virtual terminal password and login process.
D.Enter an access list and apply it to the terminal interfaces using the access-class command.
E.Create an access list and apply it to the terminal interfaces using the access-group command.
A.access-list 10 permit ip 192.168.147.0 0.0.0.255.255
B.access-list 10 permit ip 192.168.149.0 0.0.0.255.255
C.access-list 10 permit ip 192.168.146.0 0.0.0.0.255
D.access-list 10 permit ip 192.168.146.0 0.0.1.255
E.access-list 10 permit ip 192.168.148.0 0.0.1.255
F.access-list 10 permit ip 192.168.146.0 255.255.255.0
A.access-list 50 deny 192.168.1.1 0.0.0.255
B.access-list 110 permit ip any any
C.access-list 2500 deny tcp any host 192.168.1.1 eq 22
D.access-list 101 deny tcp any host 192.168.1.1
A.you can apply multiple access lists with the same protocol or in different direction.
B.you can config one access list,per direction,per layer 3 protocol
C.you can place as many access lists as you want on any interface
D.you can apply only one access list on any interface
A.They are always present in the NAT table.
B.They allow connection to be initiated from the outside.
C.They can be configured with access lists, to allow two or more connections to be initiated from the outside.
D.They require no inside or outside interface markings because addresses are statically defined.
A.network or subnetwork IP address
B.broadcast address on the network
C.IP address leased to the LAN
D.IP address used by the interfaces
E.manually assigned address to the clients
F.designated IP address to the DHCP server
A.Set the IP gateway to be used by the network.
B.Perform host discovery used DHCPDISCOVER message.
C.Configure IP address parameters from DHCP server to a host.
D.Provide an easy management of layer 3 devices.
E.Monitor IP performance using the DHCP server.
F.Assign and renew IP address from the default pool.
A.The address is removed from the pool until the conflict is resolved.
B.The address remains in the pool until the conflict is resolved.
C.Only the IP detected by Gratuitous ARP is removed from the pool.
D.Only the IP detected by Ping is removed from the pool.
E.The IP will be shown, even after the conflict is resolved.
A.Addresses are permanently assigned so that the host uses the same address at all times.
B.Addresses are assigned for a fixed period of time. At the end of the period, a new request for an address must be made, and another address is then assigned.
C.Addresses are leased to hosts. A host will usually keep the same address by periodically contacting the DHCP server to renew the lease.
D.Addresses are allocated after a negotiation between the server and the host to determine the length of the agreement.
A.reflexive
B.extended
C.standard
D.dynamic
最新試題
What are the three things that the Netflow uses to consider the traffic to be in a same flow ?()
A network administrator enters the following command on a router: logging trap 3. What are three message types that will be sent to the Syslog server? ()
Refer to the exhibit.If the router Cisco returns the given output and has not had its router ID set manually, what value will OSPF use as its router ID?()
What are two enhancements that OSPFv3 supports over OSPFv2? ()
What parameter can be different on ports within an EtherChannel?()
In GLBP, which router will respond to client ARP requests?()
What authentication type is used by SNMPv2?()
Which one of these is a valid HSRP Virtual Mac Address?()
Which three features are added in SNMPv3 over SNMPv2 ? ()
What are three benefits of GLBP?()