您可能感興趣的試卷
你可能感興趣的試題
Refer to the exhibit. You have noticed that several users in the network are consuming a great deal of bandwidth for the peer-to-peer application Kazaa2. You would like to limit this traffic, and at the same time provide a guaranteed 100 kb/s bandwidth for one of your servers. After applying the configuration in the exhibit, you notice no change in the bandwidth utilization on the serial link; it is still heavily oversubscribing the interface. What is the cause of this problem? （）
A.CEF needs to be enabled for NBAR.
B.In class Kazaa2， you should configure a policer instead of a drop command.
C.The server class should have a priority of 100.
D.The bandwidth parameter on serial 0/0 is wrong.
E.Kazaa2 is not a valid protocol.
Refer to the exhibit. As a network administrator, you have configured a dual-rate, dual-bucket policer in accordance with RFC 2698 on the serial interface of you router, connecting to your provider. The SLA with your provider states that you should only send AF31 (limited to 150 kb/s), AF32 (limited to 50 kb/s)and AF33 (best effort). Your service provider claims you are not conforming to the SLA. Which two things are wrong with this configuration?（）
A.The configuration of a service policy on half-duplex Ethernet interfaces is not supported.
B.The class class-default sub-command of the policy-map limit command should be set to the DSCP default.
C.The violate action is wrong.
D.This policer configuration is not implementing RFC 2698 dual-bucket， dual-rate.
E.The policer is configured in the wrong class.
A.Incorrect VTP domain
B.Incorrect VTP password
C.Incorrect VTP mode
D.Incorrect VTP configuration revision
A.Clear the MAC address table in the switch.
B.Clear the ARP cache in the switch.
C.Clear the ARP cache in the end devices.
D.Clear the ARP cache in the application servers.
A.The trunking configuration mode on Switch1 is set to Off.
B.The trunking configuration mode on the other end is set to On.
C.The trunking configuration mode on the other end is set to Desirable.
D.Cisco Discovery Protocol is not running on the other end.
E.There is a VTP domain name mismatch.
F.Switch1 does not support 802.1Q.
Refer to the exhibit. When applying this policy map on the tunnel1 interface，you see packet loss for the TCP class starting at around 100000 b/s，instead of the configured 150000 b/s. What is the most likely？（）
A.The violate-action command should not be configured.
B.The current configuration of the load-interval command on the tunnel interface is preventing proper policing calculations.
C.The burst size is too low.
D.Policing on tunnel interfaces is not supported.
E.The CIR keyword is missing in the policer.
最新試題
Refer to the exhibit.Which statement describes DLCI 17?（）
When upgrading the IOS image,the network administrator receives the exhibited error message.What could be the cause of this error?（）
A network administrator is troubleshooting the OSPF configuration of routers R1 and R2.The routers cannot establish an adjacency relationship on their common Ethernet link.The graphic shows the output of the show ip ospf interface e0 command for routers R1 and R2.Based on the information in the graphic,what is the cause of this problem?（）
Refer to the exhibit.What is the meaning of the term dynamic as displayed in the output of the show frame-relay map command shown？（）
what is the disadvantage of policing？
The following configuration line was added to router R1 Access-list 101 permit ip 10.25.30.00.0.0.255 any What is the effect of this access list configuration?（）
什么是NAT？
SPT初始狀態(tài)之后的一個(gè)狀態(tài)是什么？
What is method list for configure aaa？
R1 will choose which path to reach 10.1.0.0？