單項選擇題A switch is configured with all ports assigned to vlan 2 with full duplex FastEthernet to segment existing departmental traffic. What is the effect of adding switch ports to a new VLAN on the switch?()

A.More collision domains will be created.
B.IP address utilization will be more efficient.
C.More bandwidth will be required than was needed previously.
D.An additional broadcast domain will be created.


您可能感興趣的試卷

你可能感興趣的試題

1.單項選擇題Which switch would STP choose to become the root bridge in the selection process?()

A.32768: 11-22-33-44-55-66
B.32768: 22-33-44-55-66-77
C.32769: 11-22-33-44-55-65
D.32769: 22-33-44-55-66-78

3.單項選擇題What is the function of the command switchport trunk native vlan 999 on a switch?()

A.It designates VLAN 999 for untagged traffic.
B.It blocks VLAN 999 traffic from passing on the trunk.
C.It creates a VLAN 999 interface.
D.It designates VLAN 999 as the default for all unkown tagged traffic.

4.單項選擇題

Refer to the exhibit.Switch-1 needs to send data to a host with a MAC address of 00b0.d056.efa4.What will Switch-1 do with this data?()

A.switch-1 will drop the data because it dose not have an entry for that MAC address
B.switch-1 will flood the data out all of its port from which the data originated
C.switch-1 will forward the data to its default gateway
D.tch-1 will send an ARP request out all its ports except the port from which the data originated

5.單項選擇題What value is primarily used to determine which port becomes the root port on each nonroot switch in a spanning-tree topology?()

A.lowest port MAC address
B.port priority number and MAC address.
C.VTP revision number
D.highest port priority number.
E.path cost

6.單項選擇題

Refer to the exhibit. Based on the information given. Which switch will be elected root bridge and why?()

A.Switch A ,because it has the lowest MAC address
B.Switch C,because it has the lowest priority
C.Switch B,because it has the highest MAC address
D.Switch C,because it is the most centrally located switch
E.Switch A,because it is the most centrally located switch
F.Switch D,because it has the highest priority

7.多項選擇題For what two purposes does the Ethernet protocol use physical addresses? ()

A.to uniquely identify devices at Layer 2
B.to allow communication with devices on a different network
C.to differentiate a Layer 2 frame from a Layer 3 packet
D.to establish a priority system to determine which device gets to transmit first
E.to allow communication between different devices on the same network
F.to allow detection of a remote device when its physical address is unknown

8.多項選擇題Which destination addresses will be used by Host A to send data to Host C?()

A.the IP address of Switch 1
B.the MAC address of Switch 1
C.the IP address of Host C
D.the MAC address of Host C
E.the IP address of the router's E0 interface
F.the MAC address of the router's E0 interface

9.單項選擇題Where does routing occur within the DoD TCP/IP reference model?()

A.application
B.internet
C.network
D.transport

10.多項選擇題Which three statements accurately describe layer 2 Ethernet switches?()

A.Microsegmentation decreases the number of collisions on the network.
B.if a switch receives a frame for an unkown destination,it uses ARP to resolve the address.
C.Spanning Tree Protocol allows switches to automatically share vlan information.
D.In a properly functioning network with redundant switched paths,each switched aegment will contain one root bridge with all its ports in the forwarding state.All other switches in that broadcast domain will have only one root port.
E.Establishing vlans increases the number of broadcast domains.
F.Switches that are configured with vlans make forwarding decisions based on both layer 2 and layer 3 address information.